(978)686-6332 sales@nedc.com


custom gaskets

assortment of custom gaskets

Custom Gaskets are NEDCs main product. We manufacture different types of all different environments, and industries.



Gaskets are a type of solution that is an interface between two surfaces to prevent mediums such as fluid, gases, or other medias of intruding into an unwanted space. Gaskets function by providing enough stress/strain to make the gasket conform to the imperfections within surfaces it is being pressured against.



Gaskets can be subject to a number of different environmental concerns/stresses. There can be quite a few potential concerns when choosing a gasket. 

-Whether the gasket will be subject to fluids such as oil, fuel, brake-fluid, or other fluids?

-If the gaskets will do a lot of temperature cycling from low temperatures to high temperatures?

-How much compression the gasket will be subject to?

-Whether the gasket will be exposed to ozone, and UV?

-EMI/RFI shielding requirements of the gaskets, or if the gasket needs to be conductive, antistatic?

-Whether the gasket will require an adhesive backing?

These questions lead into what selections are available out in the industry for solutions. At NEDC, we are familiar with many of the selections available. 


Availability usually comes down to the same questions as above to start boiling down the potential solutions.

There are:

-High Temperature, and Low Temperature Gaskets                                      -Flame Retardant Gaskets

-UV Resistant Gaskets                                                                                          -Fuel Resistant Gaskets

-Low Compression Set Gaskets                                                                          -Ozone Resistant Gaskets

-Soft/Hard Gaskets                                                                                               -Electrically Conductive Gaskets


The above types of gaskets are made up of a combination of different types of polymers/composites/rubbers. Many of these materials can be provided in cellular form such as sponge or foam rubber materials. These selections include:

-Viton Rubber(Fluoroelastomer) FKM                                                               -Fluorosilicone Rubber (FVMQ)

-EPDM Rubber                                                                                                      -Silicone Rubber

-Urethane Rubber                                                                                                -Nitrile Rubber

-SBR Rubber                                                                                                          -Epichlorohydrin Rubber

And more



The availability goes one step further with all of the different solutions that branch out. There are plastic gaskets, sponge/foam gaskets, and VHB Tape Gaskets.


VHB Gaskets refer to VHB Tape materials provided by 3M cut into shapes that offer gasketing solutions. They are used in place of permanent fasteners. The time saved in assembly and processing can be dramatically cut down with VHB. The reason these acrylic foam tapes are used is because they offer great permanent bonding strength. In addition, they can seal out many mediums such as dust or water when properly applied. These tapes are commonly used on computer like tablets. These acrylic foam tapes include ultra thin and thick options to accommodate different applications. There are countless families of VHB Tapes to chose from. The main VHB Tape families are 4941, 5952, and RP Tapes. However, there are quite an assortment of options, including high temperature options, low temperature options, powder coated surface adhering options, and more.


Sponge/foam gaskets include cellular products that allow for less compression force. It is normally required to have significant pressure to seal out different medias properly. These materials have been chemically, or otherwise expanded. However, they are commonly made out of the same base materials as many solid rubber gasketing options. Some examples of foam/sponge gaskets include silicone sponge, fluorosilicone sponge, neoprene sponge, PORON®(urethane foam), or sponge blends. Sponge and foam gaskets are highly customizable. Some examples of that include thermally conductive options, electrically conductive options, and ultra-soft/firm options.


Silicone Sponge Products such as NORSEAL® R10400, R10450, R10460, R10470, R10480, and R10490 by Saint Gobain Performance Plastics.

-PORON® Urethane Foams by Rogers Corporation. PORON® has a huge variety of thicknesses, densities, and firmnesses available for purchase.

Silicone Foam Products such as BISCO® HT-800, HT-820, HT-840, and HT-870 by Rogers Corporation.

-Electrically Conductive Products such as Condux Plus™ from Rogers.

-Thermally Conductive Products such as Thermacool R10404 from Saint Gobain.


There are times that gaskets are made out of plastic materials instead of elastomeric ones. Some materials used include PTFE(Teflon), Nylon, UHMW, G10 Epoxyglass, and more. These materials are cut out of flat sheet materials by NEDC. As a result, the plastic we cut is usually relatively thin due to the fact we are cutting through it with either a die, laser, or a water stream.


With custom gaskets tape backings are available. These help with assembly. Many different types of peel and stick options are available. Oftentimes NEDC will apply acrylic pressure sensitive tape such as 3M 9472, or 9485PC. These high-performance acrylics stick well to most high-surface energy substrates. However, silicone pressure sensitive adhesive options are also available.


NEDC is a die-cutting manfacturer, and supplier of various cut products that utilizes waterjet cutting, laser cutting, and die-cutting to cut the above listed materials into custom gaskets. If you have an application that you believe could utilize a custom manufactured gasket, please contact sales@nedc.com.

BISCO® & PORON® are registered Trademarks of Rogers Corporation.

NORSEAL® is a registered Trademark of Saint Gobain Performance Plastics.

Gaskets Blog
Previous Posts


In our last blog, we discussed 3 tips to choosing a thermal gap filling...

read more


A lot of times when I’m explaining to someone what I do for a living, I...

read more


Closed Cell Sponge/Foam rubber materials have a place in the industry....

read more
Popular 3M Transfer Tapes to Select for your Gasket!


In one of our previous blog posts, we discussed some tips on how to pick a transfer tape for your gasket. One of the tips was, “Make sure you utilize a popular tape if you can.” The reason we said this is, popular transfer tapes are widely available, and their large...

Thermally Conductive Silicone Sponge | Custom Shapes


At NEDC, we are all about thermally conductive gap filling pads. A unique thermal gap filler that can double as a gasketing material is Thermacool R10404 Thermally Conductive Silicone Sponge. This closed-cell silicone sponge rubber gap filling material is not only...

Connector Gaskets | D-Subminiature, M83528/004XDDD


Connector Gaskets describe a type of gasket that has the geometry that would be conducive to a surface found in many connectors. This can be for two reasons. One is the requirement to have an environmental seal. The other being that EMI/RFI shielding capability is...

Oriented Wire Gaskets | Silicone, Fluorosilicone, Silicone Sponge


At NEDC, our main business is die cutting different materials. One material we see often enough is oriented wire lodged in silicone or fluorosilicone rubber material. These materials are referred to as oriented wire gaskets. These wires are oriented 90 degrees against...

Expanded PTFE, ePTFE | Custom Gaskets | Die Cutting


In one of our other posts, we discussed conventional PTFE plastic materials. Generally, we are cutting films, up to .020’’ in thickness. However, when the material is expanded and becomes mostly air, we can cut materials that are much thicker with conventional...

Super-Soft Silicone Foam Gaskets | BF-1000, BF-2000


At NEDC, soft materials are our thing. Actually, soft silicone materials are our thing. These include gap filling pads, gasketing materials, and more. One of the common issues with sealing is the amount of compression force the application can allow.  Properties of...

Bonded vs. Waterjet Cut Gaskets | Cost-Saving Techniques


One of the questions we get often especially when it comes to electrically conductive gaskets is “How can I save money on my gasket?” One of the suggestions we have is to allow bigger gaskets to be bonded from more than one piece. This is usually done through bond...

LCD Gaskets, Touchscreen Gaskets| Dust, Dirt, Water Sealing


At NEDC, we build a lot of types of gaskets. One of the more common types of gaskets we hear of is LCD Gaskets/Touchscreen Gaskets. They are everywhere now, our phones, McDonalds for ordering, and the grocery store. Typically our customers are looking for either dust...

Thin 3M VHB Tapes for Electronics | Die-Cut, Laser-Cut


At NEDC it seems like everything is getting smaller. Gaps to fill, parts to cut, leadtime to place.. Another thing that keeps getting smaller is electronics. With 3M VHB Tapes, there is no problem there. 3M VHB Tapes are used globally, and provide assistance with the...

Military Grade Gasket Materials | Specifications, Reasons to Include One


One of the best things to do when choosing a gasketing material is to pick a military specification to go along with it. There are a few reasons for this: Reasons for Choosing a Military Specification for your Gasket: It makes it recognizable for a lot of suppliers....

Silicone Press Pads, Reinforced Press Pads | Die-Cut


I hope at this point most of our customers at least somewhat think of NEDC when they think of their PCB. We make thermal pads, adhesive preforms, and RF absorbers. However, maybe they don’t think about us when they think of press pads. When PCB laminations are used to...

Top 3 Tips on Making your Gasket more Cost Effective!


Our customers come to us frequently asking about different aspects of gaskets - tolerancing, materials, thicknesses, etc. All of these can change the cost of the gasket. We thought we would make a blog on the Top 3 Tips for Making a Gasket more cost effective.  1....

All of the information presented above is believed to be factual and accurate; however, NEDC is not liable for any design or application utilizing this information.

New England Die Cutting

Popular Blog Posts


It is easy to understand why the applications of Gap Pad and Sil-Pad can be confused. This is because both thermal pads have a lot of similarities. For the most part Sil-Pads and Gap Pads are electrically isolating. Both thermal pads are thermally conductive, and both...

©New England Die Cutting 2022

澳洲5一期计划 澳洲幸运10龙虎 澳洲5开奖平台 澳洲幸运8开奖号码 澳洲10官网开奖 澳洲5全天计划 澳洲幸运8开奖结果网址 快乐飞艇历史开奖